Furuno GP-1610CF Manuel d'utilisateur

1GP-1610CFColor GPS Plotter SounderThe purpose of this Operator's Guide is to provide the basic operating procedures for this equip-ment. For mor

10Setting DestinationWhen you set a destination, this unit computes the range, bearing and course to the destination.To display your destination on th

113 Press the ENT key.4 Place cursor on destination.5 Press the ENT key twice.50k00050100150200WP801 175.0°   15nmCSE 180.0°  SPD 0.0kt

12Sailing for DestinationSet the sounder in the "Cruise" mode before leaving the harbor.1 Press the AUTO key.Steer towards destination.50k0

13Arriving at DestinationWhen nearing your destination, expand the range scale and set the sounder in the "Fish mode."Expand thedisplay rang

14Searching for FishThis section explains how to search for fish schools.1 Press the SNDR key.2 Press the s key.50k050100150200WP801 173.0°   5.2

154 Press the SNDR key.5 Press ▼ twice to select Bottom Zoom.Select thebottom zoomdisplay.7 Press ▲ or ▼ to place VRM on fish school or

16Entering MarksMarks may be used to denote the location of fish schools, good fishing spots, reefs, etc.1 Press the PLTR key.  Display theplotter/s

17Changing Mark Shape, ColorYou may wish to display marks in different shapes and colors to differentiate between reefs andfish schools, for example.

18 3 Press s twice to select "◇". 4 Press ▼ twice to select MARK COLOR.6 Press the ESC key.  7

19Returning to HarborSet your harbor as destination, and the course, range and bearing to it are displayed on the screen.1 Press the GOTO key.   3 Pre

2Do not disassemble or modify theequipment.Fire, electrical shock or serious injurycan result.Turn off the power immediately if waterleaks into the eq

20 6 Press the CLR key.7 Press the ENT key.8 Press the ESC key.9 Press the POWER key.Cancel destina-tion; turn offthe equipment.SELECT GOTO MODEWPT Li

3Inserting a Chart Card1 Turn off the power.2 Open the chart card drive cover at the bottom of the display unit.ScrewsCover3 Insert chart card label s

4Displaying the Plotter PicturePress the POWER key to turn on the equipment. A beep sounds and shortly thereafter the plotterdisplay appears.Results o

5MENUESCNU/CUENTSNDR1PLTR6AUTO2EVENTMOB 7WPT3GOTO8ZOOMOUT 9CNTR5CLRTONEPOWERZOOMIN 4CURS0321Adjusting Tone and Brilliance TONE : 5BRILL : 8LOW

6Changing the DisplayThere are ten displays. Below is the procedure for how to display the three most common dis-plays.BRG+ 232.0° RNG+ 0.00nm 2DDE

73 Press the PLTR key.4 Press ▼ to select Plotter/Sounder.SELECT PLOTTER MODEPLTR: Sel ESC: ClosePlotterPlotter/SounderDataGraphicHig

8MENUESCNU/CUENTSNDR1PLTR6AUTO2EVENTMOB 7WPT3GOTO8ZOOMOUT 9CNTR5CLRTONEPOWERZOOMIN 4CURS021How to Use the Cursor1 Press ▲ ▼ t s.PositionCursor pos

9MENUESCNU/CUENTSNDR1PLTR6AUTO2EVENTMOB 7WPT3GOTO8ZOOMOUT 9CNTR5CLRTONEPOWERZOOMIN 4CURS012,3Registering Your HarborBy registering your harbor as a